Yes,
before recompile, go to "projects/options", go to "code generation" tab and select flags:
-Run-time check of array bounds
-Run-time check of division by zero
Enable autorun only for LogicLab.
Run only LogicLab, compile and transfer. If there is some errors, you can see them on the screen (also with vnc).
[TD700] remote reboot
-
- Moderatore
- Posts: 1665
- Joined: 29/10/2010, 10:09
- Contact:
-
- Posts: 51
- Joined: 02/03/2015, 15:29
Re: TD700 remote reboot
Sorry by now I have a big problem.
I delete bin files from FTP (PlcCode0.bin and PlcCode1.bin).
I restarted IHM.
I launched LogicLab and connect to IHM (all is green with no code written so all is fine).
I downloaded code from logiclab to IHM everything was OK (SOURCE OK / CONNECTED in green).
So I did the same with Pagelab but I have a error at 15% :
I try to download again and always the same error at the same pourcentage !
I delete bin files from FTP (PlcCode0.bin and PlcCode1.bin).
I restarted IHM.
I launched LogicLab and connect to IHM (all is green with no code written so all is fine).
I downloaded code from logiclab to IHM everything was OK (SOURCE OK / CONNECTED in green).
So I did the same with Pagelab but I have a error at 15% :
Code: Select all
Transferring is 15% failed.
error T8199: Cannot download file C:\...\Cuverie MODBUS.cod => Code write failure
-
- Moderatore
- Posts: 1665
- Joined: 29/10/2010, 10:09
- Contact:
Re: TD700 remote reboot
Hi,
when this appends, you have to delete via FTP both PLCcode.bin and reboot the HMI.
when this appends, you have to delete via FTP both PLCcode.bin and reboot the HMI.
-
- Posts: 51
- Joined: 02/03/2015, 15:29
Re: TD700 remote reboot
Yes it's what I did.
I tried at least 10 times this morning and the download stop at differents percentages (15%, 48%..) but failed each time !
It is really annoying and not very stable !
LogicLab is well connected (LEDs are in green).
I found a way to generate .bin with LogicLab but can't do the same thing for PageLab
If I do this I could send file directly via FTP. There is a way to do this ?
I tried at least 10 times this morning and the download stop at differents percentages (15%, 48%..) but failed each time !
It is really annoying and not very stable !
LogicLab is well connected (LEDs are in green).
I found a way to generate .bin with LogicLab but can't do the same thing for PageLab
If I do this I could send file directly via FTP. There is a way to do this ?
-
- Moderatore
- Posts: 1665
- Joined: 29/10/2010, 10:09
- Contact:
Re: TD700 remote reboot
You can try to use this function
and then generate the code using the LogicLab opened.
and then generate the code using the LogicLab opened.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 51
- Joined: 02/03/2015, 15:29
Re: TD700 remote reboot
Ok I tried what you said.
I was able to create the file PlcCode1.bin for PageLab.
I sent it via FTP everything was OK but before the end I have been disconnected and now I cannot connect to IHM !
I was able to create the file PlcCode1.bin for PageLab.
I sent it via FTP everything was OK but before the end I have been disconnected and now I cannot connect to IHM !
-
- Moderatore
- Posts: 1665
- Joined: 29/10/2010, 10:09
- Contact:
Re: TD700 remote reboot
Sorry but I think you have some communication problems. Normally there isn't problem during FTP transmission...